fix(camera): 修掉 TP-Link 纯俯仰失效(x=0 触发固件 bug)——"上下没反应"的真因
现象:192.168.8.85 / 192.168.9.226 上"上下操作没反应,左右正常"。
定位过程:
- 协议层看是成功的(返回 200/无异常)——不对,重新看日志发现失败全集中在 up/down:
cameraPtz.log 里 69 次 `Parse Error: Expected HTTP/, RTSP/ or ICE/` 全部发生在
control(up)/control(down),left/right/斜向 0 次(8.85 家族 22 次、9.226 18 次)。
- 用裸 ONVIF 做对照实验(9.226,各 6 次):
x=0, y=-0.4 → 成功 0/6 (Parse Error)
x=0.02,y=-0.4 → 成功 6/6
再测 x=0 → 成功 0/6
relativeMove 用 x=0 同样 0/4 失败,x=0.001 则 4/4 成功。
- 也就是说这是 **TP-Link 固件 bug:ContinuousMove 的 PanTilt 里 x=0 且 y≠0 时返回畸形响应**。
左右/斜向都带 x≠0,所以从不触发;纯抬头/低头必然 x=0,于是"上下没反应"。
不同机器严重程度不同(9.226 100% 复现、8.85 大量、8.82/8.86 基本正常)。
修复:纯俯仰时把 x 从 0 换成 ±0.001(按 host 交替正负,避免 pan 单向累积)。
实测 pan 漂移约 0.0006/次,可忽略;9.226 修复后 up/down 8/8 全成功(修复前 0/6)。
同时提交上一轮未入库的两处(已部署但没提交):
- `_parseTarget` 有 camera 块时优先用 camera.port(顶层 port 属于录像机)
- `_onvifSession` 的端口候选改为 [payload port, 2020, 80](payload 给 2020 时也要能回退 80)
离线回归 46 断言全通过。
This commit is contained in:
parent
fd2b1caf8b
commit
1a27402749
@ -206,6 +206,8 @@ function _parseTarget(rtspUrl, opts = {}) {
|
||||
if (!host) throw new Error('缺少设备地址(需 rtspUrl 或 ip)');
|
||||
|
||||
const p = Number(opts.port);
|
||||
// 有 camera 块时,camera.port 才是摄像机自己的口(顶层 port 属于录像机)
|
||||
const camPort = Number(camBlock.port);
|
||||
const target = {
|
||||
host,
|
||||
// ⚠️ 凭据【不能】优先用显式字段:实测平台在密码含 @ 时把它切给了 ip 字段
|
||||
@ -215,7 +217,9 @@ function _parseTarget(rtspUrl, opts = {}) {
|
||||
username: info.username || opts.username,
|
||||
password: info.password || opts.password,
|
||||
channel,
|
||||
port: Number.isInteger(p) && p > 0 ? p : 80,
|
||||
port: Number.isInteger(camPort) && camPort > 0
|
||||
? camPort
|
||||
: (Number.isInteger(p) && p > 0 ? p : 80),
|
||||
server: null,
|
||||
};
|
||||
|
||||
@ -566,6 +570,22 @@ function _speedNormalized(speed) {
|
||||
return Math.max(0.15, Math.min(1, Math.round(v * 100) / 100));
|
||||
}
|
||||
|
||||
/**
|
||||
* 纯俯仰时用的极小 x。
|
||||
* 🐞 TP-Link 固件 bug:ContinuousMove 的 PanTilt 里 **x=0 且 y≠0**(即纯抬头/低头)
|
||||
* 会返回畸形响应(Parse Error: Expected HTTP/, RTSP/ or ICE/),所以“上下没反应、
|
||||
* 左右正常”。实测 9.226 是 0/6 全失败 → 改成 x=0.001 后 6/6 全成功(8.82 本来就正常,
|
||||
* 加上也不受影响);relativeMove 同样受这个 bug 影响。
|
||||
* pan 漂移约 0.0006/次(可忽略),并按 host 交替正负,避免长期单向累积。
|
||||
*/
|
||||
const TILT_EPSILON = 0.001;
|
||||
const _epsFlip = new Map();
|
||||
function _tiltEpsilon(host) {
|
||||
const n = (_epsFlip.get(host) || 0) + 1;
|
||||
_epsFlip.set(host, n);
|
||||
return (n % 2 ? 1 : -1) * TILT_EPSILON;
|
||||
}
|
||||
|
||||
/** 探测设备协议(结果永久缓存) */
|
||||
async function _protocol(target) {
|
||||
if (_protoCache.has(target.host)) return _protoCache.get(target.host);
|
||||
@ -646,8 +666,10 @@ async function _onvifSession(target) {
|
||||
const cached = _onvifCache.get(target.host);
|
||||
if (cached) return cached;
|
||||
|
||||
// 先试平台给的口(默认 80),再试非标的 2020
|
||||
const ports = [target.port, 2020].filter((p, i, a) => a.indexOf(p) === i);
|
||||
// 先试平台给的口,再试 2020(多数TP-Link 的 ONVIF 口)与 80。
|
||||
// ⚠️ 必须两个都留:实测 payload 给 2020 时,设备会偶发只认 80(反之亦然),
|
||||
// 去重后只剩一个口就会直接失败。
|
||||
const ports = [target.port, 2020, 80].filter((p, i, a) => a.indexOf(p) === i);
|
||||
for (const port of ports) {
|
||||
const cam = await _onvifConnect(target, port);
|
||||
if (!cam) continue;
|
||||
@ -697,8 +719,10 @@ async function _onvifAction(target, action, speed, stop) {
|
||||
const timeout = ONVIF_MOVE_TIMEOUT_MS > 0 ? { timeout: ONVIF_MOVE_TIMEOUT_MS } : {};
|
||||
if (def.kind === 'ptz') {
|
||||
const v = _speedNormalized(speed);
|
||||
const x = (def.pan || 0) * v * SIGNS.pan;
|
||||
let x = (def.pan || 0) * v * SIGNS.pan;
|
||||
const y = (def.tilt || 0) * v * SIGNS.tilt;
|
||||
// 纯俯仰:x=0 会踩到 TP-Link 固件 bug(见 TILT_EPSILON 注释),补一个极小的 x
|
||||
if (x === 0 && y !== 0) x = _tiltEpsilon(target.host);
|
||||
// onlySendPanTilt:该设备的 zoom 范围是 0~0,不同时发 zoom,避免被拒
|
||||
await _onvifCall(cam, 'continuousMove', { profileToken, x, y, onlySendPanTilt: true, ...timeout });
|
||||
_log('ONVIF 运动成功 x=%s y=%s (speed=%s profileToken=%s)', x, y, speed, profileToken);
|
||||
|
||||
Loading…
x
Reference in New Issue
Block a user